Products

Insulin Syringe

Insulin Syringe - Sungsim Medicare Medical Device
SS-INS

Insulin Syringe

Insulin Syringe

Dead space is minimized to reduce medication waste, and a precisely processed needle point enables smooth needle insertion. A range of sizes lets you choose to suit your purpose.

  • 01Production to international standards
  • 02Reduced medication waste through minimized dead space
  • 03Smooth needle insertion
  • 04A range of product sizes
  • 05E.O. gas sterilization
  • 06Domestic production (MADE IN KOREA)
Inquiry →
Insulin Syringe Product Types U-100
mL/ccSpecQuantity/InboxQuantity/Carton box
0.5mL/cc29G×13mm (1/2″)100 pcs3,600 pcs
30G×8mm (5/16″)
30G×13mm (1/2″)
31G×6mm (15/64″)
31G×8mm (5/16″)
32G×8mm (5/16″)
1mL/cc29G×13mm (1/2″)100 pcs3,600 pcs
30G×8mm (5/16″)
30G×13mm (1/2″)
31G×6mm (15/64″)
31G×8mm (5/16″)
32G×8mm (5/16″)

※ Please inquire separately for other sizes.

  1. 1

    Preparation Before Use

    1. Check the packaging condition, missing components, and expiration date.
    2. Before use, fully understand the intended use, instructions and precautions.
  2. 2

    Operation

    1. Wash hands thoroughly before use, then open the product package.
    2. Remove the protective lower cap and pull the needle cap straight off so as not to damage the needle.
    3. Disinfect the rubber stopper of the insulin vial with an alcohol swab.
    4. Insert the needle into the insulin vial and pull the plunger to draw insulin into the syringe.
    5. If air bubbles remain in the syringe, gently tap the area with air; once the bubbles rise to the tip, use the plunger to set the graduation to the desired dose.
    6. Disinfect the injection site with an alcohol swab and wait for the alcohol to dry completely.
    7. Lightly pinch the skin with the thumb and index finger, then inject.
    8. After withdrawing the needle, press the injection site gently with an alcohol swab; do not rub.
  3. 3

    Storage & Handling After Use

    1. This is a single-use product; do not reuse.
    2. After use, place it in a hard plastic container or can with a lid so the needle is not exposed, seal it with tape, and dispose of it according to the prescribed regulations.
PURPOSE · Intended Use

A plastic sterile syringe intended for injecting insulin into the human body.

WarningWARNING
  • Using a syringe unsuitable for the insulin concentration and the patient's individual dose may cause serious problems such as hypoglycemia.
  • Persons using this product should understand the intended use, instructions and precautions before use.
PrecautionsCAUTION
  • Do not use this product for purposes other than its intended use.
  • Do not use if the product or packaging is damaged or contaminated.
  • Do not use if the needle tip is damaged or the needle is bent before use.
  • As a sterile product, open immediately before use; do not pre-fill with injection fluid.
  • Note that pain during injection may worsen in the following cases.
    • When the needle coating is stripped by wiping with alcohol, etc.
    • When changing the needle direction during injection or withdrawal
    • When injecting without removing air bubbles remaining in the barrel
  • This product is single-use; discard after use and do not reuse.
Shelf lifeSHELF LIFE 3 years from date of manufacture
Storage methodSTORAGE Store at room temperature
Packaging methodPACKAGING Blister packaging (sterilization paper + PP film) or poly bag packaging
Packaging unitPACK UNIT Per manufacturer's packaging unit
Sterilization methodSTERILIZATION E.O. gas sterilization
MEDICAL DEVICE

This product is a medical device. Please read the precautions and instructions for use carefully before use.